LARGE LIGHT WEIGHT PYREX MIRROR BLANKS

(APPROXIMATE MEASUREMENTS)

DESCRIPTION

DIAMETER

1" = 25.4 mm

THICKNESS (NOMINAL) WEIGHT F/D COMMERICAL

ANNEALED

PART #

FINE

ANNEALED

PART #

16" 1 5/8" 27.00 PL* LWC1600 LWF1600
16" 1 7/8" 31.00 PL* LWMC1600 LWMF1600
16" 2 1/8" 35.00 PL* LWTC1600 LWTF1600
18" 1 5/8" 34.00 PL* LWC1800 LWF1800
18" 1 7/8" 39.00 PL* LWMC1800 LWMF1800
18" 2 1/8" 43.00 PL* LWTC1800 LWTF1800
20" 1 5/8" 42.00 PL* LWC2000 LWF2000
20" 1 7/8" 48.00 PL* LWMC2000 LWMF2000
20" 2 1/8" 54.00 PL* LWTC2000 LWTF2000
22" 1 5/8" 51.00 PL* LWC2200 LWF2200
22" 1 7/8" 58.00 PL* LWMC2200 LWMF2200
22" 2 1/8" 66.00 PL* LWTC2200 LWTF2200
24" 1 5/8" 60.00 PL* LWC2400 LWF2400
24" 1 7/8" 69.00 PL* LWMC2400 LWMF2400
24" 2 1/8" 78.00 PL* LWTC2400 LWTF2400
26" 1 5/8" 70.00 PL* LWC2600 LWF2600
26" 1 7/8" 81.00 PL* LWMC2600 LWMF2600
26" 2 1/8" 91.00 PL* LWTC2600 LWTF2600
28" 1 5/8" 82.00 PL* LWC2800 LWF2800
28" 1 7/8" 94.00 PL* LWMC2800 LWMF2800
28" 2 1/8" 106.00 PL* LWTC2800 LWTF2800
30" 1 5/8" 93.00 PL* LWC3000 LWF3000
30" 1 7/8 108.00 PL* LWMC3000 LWMF3000
30" 2 1/8" 122.00 PL* LWTC3000 LWTF3000
32" 1 5/8" 106.00 PL* LWC3200 LWF3200
32" 1 7/8" 123.00 PL* LWMC3200 LWMF3200
32" 2 1/8" 139.00 PL* LWTC3200 LWTF3200
34" 1 5/8" 120.00 PL* LWC3400 LWF3400
34" 1 7/8" 138.00 PL* LWMC3400 LWMF3400
34" 2 1/8" 157.00 PL* LWTC3400 LWTF3400
36" 1 5/8" 134.00 PL* LWC3600 LWF3600
36" 1 7/8" 155.00 PL* LWMC3600 LWMF3600
36" 2 1/8" 175.00 PL* LWTC3600 LWTF3600
38" 1 5/8" 150.00 PL* LWC3800 LWF3800
38" 1 7/8" 173.00 PL* LWMC3800 LWMF3800
38" 2 1/8" 196.00 PL* LWTC3800 LWTF3800
40" 1 5/8" 166.00 PL* LWC4000 LWF4000
40" 1 7/8" 191.00 PL* LWMC4000 LWMF4000
40" 2 1/8" 216.00 PL* LWTC4000 LWTF4000

Other sizes are available upon request.

Note: The "T" in the part number indicates a blank is approximately 2.0" thick. The part number with an "M" indicates a part that is approximately 1.7" thick. The part number without a "T" or an "M" in the product number indicates a part that is approximately 1.6" thick.

The Light weight blanks are made from Pyrex@7740 sheet material. They are thinner than the recommended standard thickness for a given blank diameter. The rule of thumb is a 6:1 (diameter thickness) ratio. The blanks are supplied in a commercial (C) annealed state (lowest anneal quality) or in a fine (F) annealed state. Please indicate which anneal is desired by ending the part number with a "C" or an "F". Precision annealed blanks are available upon request.

Please note that the above blanks come with a factory finish (i.e., rippled surfaces that are not flat). The blanks can be supplied with a ground surface or surfaces upon request. There is a charge for this service.

The blanks can be bent to a desired radius of curvature per the customer's specification. There is a charge for this service and a quotation should be requested before placing an order. Please submit a drawing of the blank with all the necessary details to facilitate the quotation process.

For a discussion on the fabrication of thin mirror blanks please refer to the following article in:

Kestner, Bob, "Grinding, Polishing and Figuring Thin Telescope Mirrors, Part 1 - Grinding", Telescope Making 12, Summer 1981, pp.30 -35.